Here are the questions people most often ask about the PIMETA v2.
You will need to know basics like how to solder, how to read a schematic, and how to wire a toggle switch. There is some surface-mount soldering required, but you can get away with doing this for just the buffers, which are relatively large SOIC-8 parts. (See Tangent Tutorial #3, a video showing how easy it is to solder this class of surface-mount parts, by hand, without any special tools.)
While it’s possible to make it your very first electronics project, you might want to get some soldering practice in on something simpler and less expensive first. I recommend the CMoy Pocket Amp, but there are many good entry level projects to choose from.
If you’re completely new to DIY electronics, first read my article Getting Started in Audio DIY.
The more you read, the more likely you’ll build the amp correctly.
At minimum you’ll need to read through the Part Selection Guide. There are no parts kits available, so you need to read this page to learn how to choose the parts you’ll use to build the amplifier. There is no single “correct” set of parts, but there are infinite wrong choices you could make. This section will tell you what works and why. Please read all the details about a part before you ask a question about it; you may be surprised at how often the answer is in the documentation.
You may also find the Part List page handy. This page lists almost everything you need to build a working PIMETA. You still need to read through the Part Selection Guide to learn how to choose among the alternatives given on that page. Also, you need other parts that cannot be listed on that page because they depend too much on your particular situation so I cannot recommend anything specific.
Once you’ve chosen your parts, you probably need to read the Step-by-Step Assembly Guide page to learn how to assemble those parts into a working amplifier. If you’re new to building amps, you may even wish to skim these sections first, because the part selection guide will make more sense when you know how the parts will be used. If you are an experienced DIYer, you may be able to skip these sections entirely.
Once the amp is working, you may wish to read through the Tweaks page.
That’s pretty much all the documentation, so the short answer is, “yes.” :)
If you don’t want to think about part values, just use the ones given on the schematic. The schematic shows a working configuration, though arguably not the best configuration for any given purpose. There is no substitute for knowledge and experience.
Most of these parts are optional only in the sense that the amplifier will function without them. The Part Selection Guide explains why you might leave some of them out, and what the consequences are.
The most effective money saving steps are to avoid the top-tier op-amps, use the ALPS RK097 instead of the other volume control options, and choose a cheap enclosure. It’s possible to leave the buffers out, but you then have to be very careful about which op-amps you choose, if you want to have a hi-fi result. If you go too far down this path, you’ll end up with something that doesn’t sound any better than the headphone output on an average receiver or integrated amp.
Yes. The parts table is a list of examples, not a prescription.
Before buying a part not mentioned on these pages, do a search in the Head-Fi DIY forum archives; someone else may have used the part and reported on it, or there may be advice there saying why a given part is a bad choice for a PIMETA. If you can’t find any information there on the part and you aren’t savvy enough to be able to pick parts on your own, please ask on the forums about it. Often a part that looks like it will work, won’t.
Sorry, no one’s offering kits right now, and I have no plans to ever offer kits. You can get everything you need to build this amplifier with a single order to one of the major electronic parts distributors.
If you’ve looked through the docs and have concluded that you’d really rather not build the amp yourself, you can look for a builder on the forums. There are several active builders. I am not one of them.
The PIMETA was designed with headphones in mind. Headphones are completely passive, with no connection to the input side of the amplifier, so we are able to split the ground circuit into two parts, to good effect.
If you were to use a stock PIMETA as a preamp, the cabling situation in typical source-preamp-amp configurations shorts out the ground channel. At minimum, this will defeat the ground channel, making it a waste of good parts. More likely, it will cause the circuit to misbehave, potentially even to the point that it damages itself or something downstream.
It’s easy to modify the PIMETA so it will work correctly in a preamp role. To keep using the PIMETA with a single-rail power supply, you can leave out OPAG, R7G, and BUFG, running a jumper from the +IN on OPAG to the second OG pad, effectively connecting IC2’s output to OG. Alternately, you can power the PIMETA from a dual-voltage power supply (see the Tweaks page), leaving the ground channel out entirely.
First, look through this documentation. It has been improved continuously since the introduction of the PIMETA v2, and it benefits from previous designs’ documentation, so the answer is often here if you look carefully enough.
Next, look through my articles list. I’ve written quite a few of these articles now, one of which may answer your question. Naturally I don’t wish to repeat myself here in the PIMETA documentation, and sometimes I don’t point to a suitable article when I should.
If you can’t find it here, do a search in the Head-Fi DIY forum archives. Asking a question that’s been answered before (sometimes many times before) is a waste of the other forum members’ time and yours. If the answer is in the archives, it’s quicker to search the archives than to post the question and wait for people to answer.
If the answer is not in the archives, go ahead and post the question to the forum. It’s better to post publically than ask people via email or private messaging because you get more answers by posting publically, and the answers are archived for future builders to find.
This space intentionally left blank. :)
<< PIMETA v2 Headphone Amplifier
||Part List >>|
|Updated Fri Dec 16 2022 12:23 MST||Go back to Audiologica||Go to my home page|